文文文档档档说说说明明明 Thank you for choosing our solar controller product. This product manual will include product function properties, installation, usage, trouble clearance and so on. Before use, customer must read this.
Get a quote >>
Pay attention to the load, battery, solar panel and controller of same polarity. Put into the external temperature sensor on the left of the controller (probe port). The temperature sensor should be similar space with battery. (Otherwise, the controller will control the parameters of all wrong temperature compensation.)
Customer Service4.4 Solar Panel Fault and Treatment Symbol flashing represent the controller was not detected solar panels within 24hours. Check if there is a connection from solar panel, check if there is an open circuit between solar panels with controller. 4.5 Load Shock Fault Open load if the flashing, that indicate the load impulse current is more than
Customer Service1h～23h: said Light Control with Time Control Mode, Load power after dark, and close the load according to the timer setting. 0h: said Light Control Mode, Load power after dark, turn off the load after drawn. In this interface, numbers start flashing, that has entered the Load Working Mode set
Customer ServiceMultiple load control modes: 24Hours Working Control, Light Control, Light and Dual Time Control; Automatic temperature compensation and accumulated function of charge and discharge KWH; Double USB output 5V/2A; Perfect electronic protections; Solar Charge Controller BSC8048 Series Specification:
Customer ServiceSolar Panel Fault and Treatment Symbol flashing represent the controller was not detected solar panels within 24hours. Check if there is a connection from solar panel, check if there is an open circuit between solar panels with controller. Load Shock Fault
Customer ServiceAnti-high Temperature Barrier Intelligent flashing solar road warning light JS-671 - JYSUN Products Made In China, China Manufacturer. 1.Solar Panel:2V/200MA Monocrystalline 2.Storage:1.2V/1200MAh Ni-MH battery 3.Lighting Time:100h after fully charged 4.Work Mode:Flashed for 90times per minute or Stable 5.LED Color:Red Yellow Blue Green White
Customer ServiceSolar Panel Fault and Treatment： Symbol flashing represent the controller was not detected solar panels within 24hours. Check if there is a connection from solar panel, check if there is an open circuit between solar panels with controller. Load Shock Fault：
Customer Service1h～23h: said Light Control with Time Control Mode, Load power after dark, and close the load according to the timer setting. 0h: said Light Control Mode, Load power after dark, turn off the
Customer ServicePay attention to the load, battery, solar panel and controller of same polarity. Put into the external temperature sensor on the left of the controller (probe port). The temperature sensor should be
Customer ServiceThis intelligent, multi-purpose solar charge and discharge controller has a very friendly interface of fixed LCD display. Various control parameters can be flexibly set, fully meet your various application requirements. It has following features: Vivid
Customer Service• Temperature compensation function. The controller can automatically adjust the charge parameters of battery by environment temperature to lengthen the service life of battery. • Sophisticated electronic protection production, including overcurrent protection, load short-circuit protection and low-voltage protection.
Customer ServiceBefore connecting the device, make sure that the energy supply matches the specifications that controller requires. All devices connected to the controller must conform to the technical
Customer Serviceevery installation into a potential water leak time bomb. No major composite shingle manufacturer, such as GAF, CertainTeed or Owens-Corning, endorses or approves non-flashing based solar mounting systems for use with their roofing materials. Practically, this transfers Flashing Requirements for Roof-Mounted Solar Arrays
Customer ServiceHow to troubleshoot and fix solar charge controller blinking and flashing lights. If you are experiencing blinking and flashing lights on your solar charge controller, the first step to take is to identify the specific lights that are blinking or flashing.
Customer ServiceSolar Panel Fault and Treatment Symbol flashing represent the controller was not detected solar panels within 24hours. Check if there is a connection from solar panel, check if there is an
Customer Service4.4 Solar Panel Fault and Treatment Symbol flashing represent the controller was not detected solar panels within 24 hours. Check if there is a connection from solar panel, check if there is an open circuit between solar panels with controller. 4.5 Load Shock Fault Open load if the flashing, that indicate the load impulse current is more than
Customer Service30 Watt Solar Intelligent Controller Install Guide download. Datasheet download. 30 watt Summary. The core of the TraffiCalm® Flashing Sign systems, the Intelligent Controllers and Collaborators, are the "brains" of the group. These devices handle everything from flash rate to automatic brightness control to scheduling. Specifications. PHYSICAL DESCRIPTIONS
Customer ServiceHow to troubleshoot and fix solar charge controller blinking and flashing lights. If you are experiencing blinking and flashing lights on your solar charge controller, the first step to take is to identify the specific lights that are
Customer Service• Multiple load control modes: 24Hours Working Control, Light Control, Light and Dual Time Control. • Automatic temperature compensation and accumulated function of charge and dis
Customer Service• Multiple load control modes: 24Hours Working Control, Light Control, Light and Dual Time Control. • Automatic temperature compensation and accumulated function of charge and dis-charge KWH. • Double USB output 5V/2A. • Perfect electronic protections.
Customer Service1h~23h: said Light Control with Time Control Mode, Load power after dark, and close the load according to the timer setting. 0h: said Light Control Mode, Load power after dark, turn off the load after drawn.
Customer Servicesolar geyser is installed, the sun may heat the water beyond the temperature set on the unit. The water temperature is set to a factory default of 55°C. The temperature can be set in four different time slots: Temperature setting 1 applies to the time slot 00h00 to 05h59 Temperature setting 2 applies to the time slot 06h00 to 11h59
Customer ServiceSolar Panel ： Load sensor control ： The system is working correctly ： The system is not working properly ： Battery charge capacity instruction ： Load timer control ： Battery . 2 Description of Button Function: : Interface loop switch button, use the button to cycle between pages in each switch cycle sequence shown in (figure 1) : Adjustment of parameters plus
Customer ServiceBefore connecting the device, make sure that the energy supply matches the specifications that controller requires. All devices connected to the controller must conform to the technical specifications of the controller. All operations on an open controller are only to be conducted cleared from the power supply.
Customer ServiceSolar Panel Fault and Treatment： Symbol flashing represent the controller was not detected solar panels within 24hours. Check if there is a connection from solar panel, check if there is
Customer ServiceThis intelligent, multi-purpose solar charge and discharge controller has a very friendly interface of fixed LCD display. Various control parameters can be flexibly set, fully meet your various
Customer ServiceBattery Voltage Battery Solar Panel (main interface) temperature charge current Accumulated Accumulated Load Discharging power(Ah) charging power(Ah) discharge current Figure 1 3 View the parameters Thecontrollerwilldefaultentry"batteryvoltage"interfaceaftercorrectpower-on.This is them ain interface. Use the button could in turn visit the following parameters interface 3.1
Customer Service1h~23h: said Light Control with Time Control Mode, Load power after dark, and close the load according to the timer setting. 0h: said Light Control Mode, Load power after dark, turn off the
Customer Service2.4 To connect the solar panel and the controller by cables with right polarity. If there is sunshine and is correctly connected,the solar icon will be on, otherwise,to check and reconnect . 2.5 To connect your load and the controller with right polarity. Pay attention to + - polarity to avoid reversed connection, otherwise, your load may be damaged. Demolition: In case of any
Customer ServiceThe icon and lights on the solar controller flash or change color for the solar panels, battery, and loads that are explained as fellow. Solar panel flashing green light When the solar controller detects solar energy input, the PV icon and light will blink for a few seconds, and then enter a stable state.
Solar panel flashing green light When the solar controller detects solar energy input, the PV icon and light will blink for a few seconds, and then enter a stable state. The screen will not light up and the indicator light will not light up if the solar regulator does not detect the solar input.
solar charge controller battery blinking green means the battery is fully charged and in a saturated state, A flashing red battery light means the battery is undercharged and needs to be recharged in time. Solar controller loads are small DC devices that can be powered directly by a solar battery.
The controller has enter into Short Circuit Protection state Check the load if there is damage or not, if there is cable short circuit or not, after trouble shooting short press the button for restoration. Symbol flashing represent the controller was not detected solar panels within 24hours.
Solar controller loads are small DC devices that can be powered directly by a solar battery. They are displayed as light bulb icons on screens and LED lights. On the screen, when the load icon flashes, there is an overload of short circuit. In the indicator light, if the load indicator is green, it means the load is operating normally.
When temperature sensor’s (T1) wiring is interrupted, not connected or short circuit, controller switches off the corresponding signal output, and simultaneously “- - -” error code displays on the screen. 9. Quality Guarantee The warrantee expires within 12 months after the date of purchasing the controller.
Our dedicated team provides deep insights into solar energy systems, offering innovative solutions and expertise in cutting-edge technologies for sustainable energy. Stay ahead with our solar power strategies for a greener future.
Gain access to up-to-date reports and data on the solar photovoltaic and energy storage markets. Our industry analysis equips you with the knowledge to make informed decisions, drive growth, and stay at the forefront of solar advancements.
We provide bespoke solar energy storage systems that are designed to optimize your energy needs. Whether for residential or commercial use, our solutions ensure efficiency and reliability in storing and utilizing solar power.
Leverage our global network of trusted partners and experts to seamlessly integrate solar solutions into your region. Our collaborations drive the widespread adoption of renewable energy and foster sustainable development worldwide.
At EK SOLAR PRO.], we specialize in providing cutting-edge solar photovoltaic energy storage systems that meet the unique demands of each client.
With years of industry experience, our team is committed to delivering energy solutions that are both eco-friendly and durable, ensuring long-term performance and efficiency in all your energy needs.